I reached out to my contact at Reese and the Replacement 1/2" Hardened Washer for Reese Weight Distribution Systems # 3306 you were looking at are the correct washers to adjust the hitch ball angle on your Reese Pro Round Bar Weight Distribution w Sway Control # RE44FR.
I included a video of the # RE44FR for you to take a look at. view full answer...
For a shock kit for your 2021 Winnebago 2401 Minnie with 3,500 lb axles you'd want the part # LC281255. Since hangers don't typically have grease fittings I believe what you are looking for would be cushioned equalizers like the Road Armor part # LC696740 which are correct size and rating for your trailer. view full answer...
You are correct, the Furrion Marine Power Inlet # F30ITSBS is a direct replacement for your Furrion F30INSBS. Since you are needing a new power inlet I recommend going ahead and getting the # F30ITSBS due to this.
I included a video of the # F30ITSBS for you to take a look at. view full answer...
We have a jack that matches exactly what you are looking for.
I recommend the Lippert Smart Jack Electric Trailer Jack w/ Footplate # LC643589 which has a 3500lb weight capacity and allows you to set the height you want the jack to raise and lower to so that you can raise or lower the jack with the touch of a button and not have to hold a switch.
The # LC643589 will replace the standard A-frame trailer jack in your trailer.
For a bumper mounted cargo carrier I recommend taking a look... view full answer...
For additional rear facing style cameras to use with the Voyager Wisight part # ASA37YR that you plan to install on your 2021 Winnebago Minnie you'd want the Replacement camera part # ASA74YR which you could use in any of the locations you mentioned. view full answer...
Yes, you will need to add the tongue weight of your 2020 Winnebago Minnie 2201MB to the axle weight of 4780lb to get the total weight unless you unhooked the trailer and put it on its jack on the scale.
Since your tongue weight is between 800-850lbs a perfect weight distribution hitch is the Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW # FA92-00-1000 which works with tongue weights between 600-1000lbs, and it has built in 2-point sway... view full answer...
The Adco SFS AquaShed Cover, # 290-52240 fits travel trailer 18'1" - 20' long. This cover works best for short-term storage in moderate climates. It has a heavy-duty, 3-layer fabric that protects against rain, snow, and sun, is contoured to match the shape of your trailer. To determine the proper fit, measure the length (not including the trailer tongue) and sidewall height (undercarriage to the top of the natural roof line). Please note the attached image. view full answer...
Your battery is quite a bit larger than most breakaway batteries so for a box you'd have to go a slightly different route with something like the part # DW03009 which has inner dimensions of 10-3/4 inches long, 7 inches wide, and 8-1/4 inches deep. view full answer...
I suggest the Solera RV Slide-Out Awning - 9'7" Wide - 48" Projection, # LCV000163292 for white or # LCV000251461 for black.
For determining the proper size Solera Slider you need, to measure the total width of your slide room from the outside including the flange then add a minimum of 5" (2-1/2" each for the left/right side overhang). You can have greater than 2-1/2" overhang if you want, but it is suggested that you do not go any less. The measurements you provided are 109-1/2". The... view full answer...
While we don't have any air spring kits that fit your 2020 Winnebago Minnie travel trailer we do have Timbren kits like the # TTRA1032 which can be used on trailer suspension to provide addition suspension support. These do provide even support for both sides of the axle though and there isn't a way to provide more support to one side than the other. view full answer...
The TireMinder TPMS for Dual Axle Trailers part # TPMS-TRAILER as you stated is only for trailers 25' or shorter. The Winnebago Minnie 2500FL measures 28' 3" long so I cannot recommend this. There isn't another solar powered version like this for longer trailers either so you will have to consider other options like the TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster part # TM89FR. The main difference is the monitor which will take up some space on your windshield and plugs into... view full answer...
The easiest and most cost effective way to increase ride quality on a travel trailer like the Winnebago Minnie is to upgrade to cushioned equalizers. These will provide significant increases in smoothing out the ride. I recommend the Dexter E-Z Flex Suspension Kit as it's more of a complete kit since it comes with cushioned equalizers, wet bolts, and heavy duty shackles. The correct kit will be based on your axle spread, part # K71-652-00 for 33" or part # K71-653-00 for 35". view full answer...
For determining the proper size Solera slide-out awning, you need to measure the total width of your slide room from the outside including the flange and then add a minimum of 5" (2-1/2" each for the left/right side overhang). You can have greater than 2-1/2" overhang if you want, but it is suggested that you do not go any less. If you have done so with resulting measurement of 96" you need an awning no less than 101". You can go beyond the overhang of 2.5" each side if you choose, no worries.... view full answer...
I would be happy to help!
Since the horizontal mounting hole measurement of the equalizers on your 2016 Winnebago 2351DKS is 5-1/2" there are a few different equalizer upgrade options.
To determine which one will be best for you, you will need to measure from the center line of the horizontal mounting holes to the center of the upper mounting hole which will tell you how tall your equalizer is.
The Road Armor Shock Absorbing Equalier # LC696740 you were looking at is a great option that... view full answer...
Go To Results